Home    Company Information    Contact Us

Corporate Information

Products
Continuous Emission
    Monitoring Systems
    In situ

        SM®8200

        SM®425

    Standard Extractive
    Dilution Extractive

Flow Monitors

    UltraFlow 150

Gas Monitors

    T SERIES

Opacity Monitors

    LightHawk®

Particulate Monitors

    LaserHawk®

    LaserHawk® 360P

Software

    RegPerfect®

    RegPerfect.net

Useful Information
Trade Shows
Quality Policy

Links

Support
Customer Service

Service
Opacity Attenuator (Filter)
    Certification

Call Center

Training
    Hardware Training
    Software Training

Product Status

Manuals

Firmware Downloads

Sample Specifications

Contact Us
Visiting Our Facility

Representatives and
   Distributors


Where to Stay

Career Opportunities


Terms and Conditions

Installation Checklist Lighthawk® 560

* Your order cannot be scheduled for production until accurate information is provided for all fields marked with an asterisk.

» Download this Document
» How to Use this Document


CUSTOMER CONTACT INFORMATION

Name:  *
Title:
Company:  *
Phone:  *
FAX:
Email:  *
Stack Identification:  *

2. MOUTING FLANGE ( Select One of the following)  *
I will supply my own 2 inch flanges for the Standard Installation
I wish to use something other than 2 inch flanges, described below:


3. FLANGE TO FLANGE DISTANCE (Complete ONE of the Following) *  
Feet       Inches       Meters
4. TEMPERATURES (SELECT ONE OF THE FOLLOWING FOR EACH GROUP

A. PROCESS  *

Less than 500 Degrees Fahrenheit (290 Degrees Celsius)
501 to 1500 Degrees Fahrenheit (261 to 815 Degrees Celsius)
less than 1500 Degrees Fahrenheit (less than 815 Degrees Celsius) Consult Factory

B. AMBIENT (STACK)  *

-25 to 140 Degrees Fahrenheit (-32 to +60 Degrees Celsius)
Other, Consult Factory
 
C. AMBIENT (REMOTE)  *

+32 to 104 Degrees Fahrenheit (0 to 40 Degrees Celsius)
Other, Consult Factory


5. PROCESS PRESSURE (SELECT ONE OF THE FOLLOWING)

-15.0 to 5.0inches H2O (-3.745 to +1.245 kilopascal)
-15.0 to 15.0inches H2O (-3.745 to +3.745 kilopascal)
Other, Consult Factory


6. MOUNTING CLEARANCE (SELECT ONE OF THE FOLLOWING)

The standard Mounting Clearance is sufficient.
I will use something other than the standard Mounting Clearance, described below:
 

7. PURGE FAIL CABLE LENGTH (SELECT ONE OF THE FOLLOWING)

The standard Purge Fail Cable Length of 40 ft. is sufficient.
I will use something other than 40 ft. of Purge Fail Cable, described below:
 

8. DATA CABLE LENGTH (The data cable is supplied at an additionalcost.)

I wish to purchase:

Feet of Data Cable

9. STACK POWER CIRCUIT REQUIRMENTS
Optical Head: 85-245 VAC, 47-63Hertz, Single Phase, 30 VA Maximum
Single Purge Blower Number: 115/230 VAC, Single Phase, 414 VA Maximum
Dual Purge Blower Number: Two circuits, each with the same requirements as a Single Purge Blower
Number (#): Does not apply to instrument Air Purge Version


10. CORRECTION FOR EXIT PATHLENGHT  *

Monitor Pathlength: Feet Inches
Outlet Pathlength (round): Feet Inches

or

Rectangular Exit Width:  Feet Inches
Rectangular Exit Length: Feet Inches

or

Desired Pathlength Correction Factor:
   
If you are requesting a specific Pathlength Correction Factor value, please explain:


11. MAXIMUM OPACITY LIMIT  *
Instantaneous Opacity Limit   Average Limit
less than 20% Opacity less than 20% Opacity
greater than or =20% Opacity greater than or =20% Opacity


12. SPECIFY FULL SCALE

Opacity:

Optical Density:
Particulate Mass:


13. USE AUTO CAL SEQUENCE? (SELECT ONE OF THE FOLLOWING)


YES
NO


14. SYSTEM CONFIGURATION (SELECT ONE OF THE FOLLOWING)
Direct Interface
Enhanced Remote Panel


If you selected the Direct Interface Configuration, fill out the following:
Output Units: Opacity Optical Density Particulate Mass, Consult Factory
Current Outputs: 4 to 20 milliamp 0 to 20 milliamp
Relay Output #1:
Relay Output #2:
Digital Input #1:
Digital Input #2:


Only if you selected the Enhanced Remote Panel Configuration, fill out this page:
Analog Output #1:
Analog Output #2:
Analog Output #3:
Analog Output #4:

Relay K1:
Relay K2:
Relay K3:
Relay K4:
Relay K5:
Relay K6:
Relay K7:
Relay K8:


Ethernet Module Setup
Use a Dynamic Internet Provider (IP) address
Use a Static Internet Provider (IP)>address, if yes please supply the information below:
Static IP Address  
Subnet Mask  
Default Gateway


Enhanced Remote Panel Power Circuit Requirements:
85-245 Volts Alternating Current, 47-63 Hertz, Single Phase, 30 Volts Alternating Current Maximum
115 Volts Alternating Current Power Cord 230 Volts Alternating Current Power Cord

Enter code to confirm submission
Confirmation:   Validation Enter Confirmation Code:   *
 
 





Home | Warranty | Terms of Use | Service & Support | Products | Contact Us

Copyright © 2016 Teledyne Technologies Incorporated. All rights reserved.
35 Inverness Drive East - Englewood, CO 80112